Cerber C52 is a burglar alarm system with 6 fully programmable zones on the motherboard, expandable to 12 by doubling and / or using keypad zones (each. Cerber c Users Guide – Download as PDF File .pdf), Text File .txt) or read online. Cerber C Zone and 2-Partition Burglary Control Panel For your home and office User’s Guide Doc / / version 1. INTRODUCTION.

Author: Akinonris Zologami
Country: Armenia
Language: English (Spanish)
Genre: Politics
Published (Last): 24 October 2015
Pages: 304
PDF File Size: 6.43 Mb
ePub File Size: 9.99 Mb
ISBN: 926-7-36746-432-6
Downloads: 53014
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzragore

Section [] — Manually Activation of PC callback Please note the backup battery is continuously charged while AC power is present and if this trouble persists for a long time that means the battery must be replaced.

Once a delayed zone is first violated during one armed period it will start the appropriate entry delay timer; the keypad buzzer will sound a continuous beep, indicating that the system must be disarmed.

That means if master user is trying to change his rights by pressing any key from 1 to 7, the keypad buzzer will sound a long error beep and the control panel will reject the command.

Arming can be performed with one or more bypassed zones, even if the sensors on these zone loops are faulted. Section [] — Walk Test service mode The most frequent cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This trouble indicator will appear if wiring between the siren and the control panel is shorted, cut-off or there is an overload on the siren control wire a 3K3 resistor must be connected across the bell terminals. Then enter the following sequence: The system time and date are necessary for correct recording of the events into the event LOG.

They cannot detect motion or intrusion that takes place behind walls, ceiling, floors, closed doors, glass partitions, glass doors or windows. In order to choose one of the options, just press the cerbfr key i.

The user code must have the right for arming. This trouble indicates that the battery is disconnected or its voltage is lower than System Troublesand when enetring the menu: The user code must have the disarming siren stopping right; After entering the first code digit, the continuous beep will stop and upon each key pressing, the keypad buzzer will sound a short confirmation beep. This trouble csrber will be ON when: Bypassed zone creber is only valid during a single arming period; upon system disarming, bypassed zone status will be automatically cleared by the panel.

TOP Related Articles  BROTHER 7065DN SCAN TO PDF

After all sensors in the system was tested, press [ ] key to exit this testing mode.

Cerber c612 Users Guide

This alarm system should be tested weekly to make sure that all sensors work properly. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as chimneys, in walls, or roofs, or on the other side of closed doors.

The programming sections allowed to the master user are: Program the inactivity autoarming time as it is described in [] section. All LEDs from 1 to 7 will be ON or OFF, as the respective rights were established by the installer previously; the master rights cannot be changed by him.

If in this section, one of the 2 groups of ccerber digits are set both with value 0, then the corresponding partition will try to auto arm after every second if no activity will be detected in the area.

System Trouble Status Displaying: On LCD keypads you can see after arming in this mode one text similar cerebr For system parameter programming to be accomplished only by authorized people, this code must be changed after the system was installed! If [8] key is pressed and the zone 3 LED is blinking, then the 8-th memorized alarm was triggered by zone 3. Once the system enters section [], it will exit this section only after [ ] key is entered the control panel will not leave this section automatically, 2 minutes after the last key pressing any more.

In this mode, zone LEDs 1 to 6 and keys [1] to [6] are used to perform the bypassing or un-bypassing procedure for zone 7 to zone 12 respectively.

TOP Related Articles  DECADENT SHAYLA BLACK PDF

Allowed default rights for these user codes are: These events occur by activating the correspondingly 24h defined zones, or by simultaneously pressing a combination of keys from keypad: After that, the user must leave the objective before the exit delay elapses.

The control panel will no longer consider the detectors from a bypassed zone. In case there is no voice module on the main board or it was deactivated, the panel will report upon remote interrogation calls or to the follow me phone numbers only by specific synthesis sounds. The menu command list is the following: If the siren sound is stopped while the system is disarmed, using a proper user code, the system will not be armed in the meantime, only the sounders stops.

The following operations can be performed: Keypad types The next keypad models are available: Other Operation Commands Performed by the master user Some of programming sections, which are dedicated to the installer, are accessible to the master user, too.

To cancel the command user can press [ ] key.

Cerber C – Roel Design

Choose partition 1,2, The options displayed on the 2nd line state for choosing partition A 1partition B 2 or cancel command. In this case, if the user wants to arm the system after the siren sound was stopped, he must key in again the user code. Zone 7 LED [4]Display trouble Tamper Zone Tamper This trouble condition is displayed if any of the zones that have enabled tamper recognition is in tamper condition.

If after entering the last digit of the user code the keypad buzzer is sounding a long rejection beep means: Even if no successful command was performed, the user should press [ xerber key in order to exit from the display of PGM1 to PGM6 status.